How to's for Replica Racers
-
toratora
- Posts: 3161
- Joined: Wed Oct 11, 2017 1:05 am
- Location: San Francisco
- Replica: Derbi GPR
Cagiva Mito
Cobra CX65
Aprilia RS50
- x 1768
- x 1977
-
Contact:
Post
by toratora » Sun Jun 17, 2018 1:39 am
What have people done to source castle sockets for adjusting the swing arm on the 99/2005 RS50, the RS4s, and the 2010+ GPRs?
Amazon has a number of castle sockets available for affordable prices—however I don’t know the tool size.
Derbi did produce an official product.
MODEL GPR 50 125 2009 DATE SEPT. 2009 CIRCULAR No 255.370
866714 Tool to adjust swing arm nut on the GPR 2009
Dear dealer,
We are pleased to announce you that we extended our range of special tools. We now propose through our spare parts department, a special key to mount the swing arm of the models GPR 50 2T 2009 and GPR 125 4T 4V 2009, under the ref 866714.
This tool is in particular necessary to adjust the nut number 8, ref. 865615, in the spare part scheme that you find below.
Kind regards,
After-Sales Service Nacional Motor S.A.-DERBI
![Image](https://i.imgur.com/1BJhfm7.jpg)
1 x
-
toratora
- Posts: 3161
- Joined: Wed Oct 11, 2017 1:05 am
- Location: San Francisco
- Replica: Derbi GPR
Cagiva Mito
Cobra CX65
Aprilia RS50
- x 1768
- x 1977
-
Contact:
Post
by toratora » Wed Jun 20, 2018 12:32 am
Yeah that would be great. It would be really nice to have something that folks could order here in the States from places like Amazon.
Thanks!
0 x
-
toratora
- Posts: 3161
- Joined: Wed Oct 11, 2017 1:05 am
- Location: San Francisco
- Replica: Derbi GPR
Cagiva Mito
Cobra CX65
Aprilia RS50
- x 1768
- x 1977
-
Contact:
Post
by toratora » Sun Jan 13, 2019 2:39 am
With everything boxed up it’s been a righteous challenge to get anything done. Today I found the calipers, and thought it would be nice to finally measure that 2005 RS50 swing arm castle nut.
The inner dimension is about 24.46mm, and the outer dimension is about 28.57mm. Hopefully that will be sufficient information for sourcing an affordable, workable tool. I probably should have also tried to measure the width of the finders.
![Embarrassed :flushed:](./images/smilies/flushed-face_1f633.png)
1 x
-
Berkeley
- Posts: 297
- Joined: Sun Sep 02, 2018 5:24 pm
- x 332
- x 147
Post
by Berkeley » Tue Feb 12, 2019 1:39 pm
.
The guys from
gbmotorcyles managed to modify their stock one to fit the nut. They sent a new one free of charge!!
Although the socket should have been 3mm overall bigger (so that the teeth were not so thin) It still fitted fine and it came off without any problem.
2 x
-
toratora
- Posts: 3161
- Joined: Wed Oct 11, 2017 1:05 am
- Location: San Francisco
- Replica: Derbi GPR
Cagiva Mito
Cobra CX65
Aprilia RS50
- x 1768
- x 1977
-
Contact:
Post
by toratora » Wed Dec 11, 2019 3:39 pm
I’ve been chatting with Luke over at
GB Motorcycles about these sockets and nuts. He checked out this page and based on Berkeley’s measurements Luke is having a batch of sockets made for the newer bikes. This is totally awesome news!! Thanks so much Luke!!
Luke is going to let me know when they are ready, and I’ll post a link in this thread when they are available.
![Paw Prints :paw_prints:](./images/smilies/paw-prints_1f43e.png)
2 x